Webasto Thermo Top Comfort+

Buy Webasto Thermo Top Comfort+

Liquid heater Webasto Thermo Top Comfort+ is designed for: • heating of the car interior • defrosting of Windows • pre-heating of the car engine of liquid cooling. Perfect for cars with an engine capacity of 2 to 4 liters. Article 9036778, 9036779

Only 1 left in stock
$600

Pre-heater Webasto Thermo Top Comfort+
It has significantly smaller dimensions than previous models, which allows you to install the heater in modern cars with extremely dense layout of the engine compartment. The engineers managed to reduce not only the overall dimensions, but also to reduce fuel consumption by 30% compared to the Thermo Top C series. Economy, high heating capacity, minimum dimensions and low weight made the Top Evo 5 the flagship among the heaters for cars. Designed for cars with engine capacity from 2 to 4 liters.

Heater supply set:

1 - Webasto Thermo Top Comfort replacement Heater+ 5 kW

2 - Circulation pump U 4847 econ 12V (Ø 18mm)

3 - dosing Pump DP 42 12V (petrol and diesel) with mounting

4 - Set of fittings for connection to the heater 2x900 Ø18mm, two spring clamps Ø25mm 2pcs – 90 deg. x18mm

5 - Pack with connecting fittings. Composition: angle fitting 900 x - 2 PCs, self-clamping clamp Ø25mm - 6 PCs

6 - Pack with connecting fittings. Composition: angle fitting 900 - Ø18x18mm - 1 PC straight fitting Ø18x18 mm - 1 PC self-clamping clamp Ø 25 mm – 6 PCs

7 - liquid Hose L= 2m Øvnutr.= 18 mm, Øvnesh.= 18 mm

8 - pressure plate for liquid pipes, two rubber seals, mounting screw

9 - Package with u4847 econ circulation pump bracket, M6 mortgage nut, M6 bolt, bushing

10 - Pack with exhaust clamps and fasteners

11 - a Package of fasteners

12 - exhaust Silencer Ø22mm

13 - exhaust Pipe D=22, d=25.5, L=1000 mm

14 - Package with remote metallized, heat-resistant rings (red) 2 PCs.

15 - air intake Tube Øvnutr 21.4 mm, L= 400 mm.

16 - Pack with intake air silencer, retainer

17 - Packing of cable ties. 40 PCs

18 - standard Bracket

19 - Pack of connecting fuel pipes

20 - wiring Harness main (sealed)

21 - fuse and relay Holder (in-room)

22 - circulation pump Harness

23 - Pack with elements for power connection of the motor of the fan of the cabin stove

24 - Pack with fuel intake

25 - Fuel tube, black 1,5x5mm, L = 5m.

26 - Package with documentation

Composition of Webasto Thermo Top Comfort+heater.

Webasto Thermo Top Start 5 consists of the following main components:

- Air blower with control unit. Disassembly of the supercharger is not allowed!

- Burner

- Coil

- Glow pin / flame sensor

- Temperature sensor and overheating sensor

- Circulation pump

- Dosing pump.

The principle of operation of Webasto Thermo Top Comfort+.

Starting the heater is via the signal to switch on from the control. The Thermo Top Evo can only be started by a control unit with a WBus bus or by PC diagnostics Thermo Test. When the heater is started, the supercharger, the circulation pump and the filament pin start to function. Then the metering pump is switched on. The petrol heater is started at maximum load. The diesel heater is started with a minimum load and slowly accelerating, goes to the maximum load. During the start phase, the glow pin controls the formation of the flame. After entering the maximum load mode, the filament pin performs the controlling function of the flame sensor. The heater with reaching a certain temperature (about 80°C) goes into energy-saving partial load mode. If the temperature increases further, the heater is switched off from a certain temperature (about 84°C) in the adjustment pause mode. The Gorenje process is stopped when the signal for shutdown is received, when the limit combustion temperature is reached, when the set operating time is reached, or when an error occurs.

Heater Mode Thermo Top - B Thermo Top - D
5 kW 4 kW 5 kW 4 kW
EU certificate numbers e1*2001/56*2006/119*0258*ahhh!.. e1*72/245*2006/96*5627*ahhh!..
E1 122R-00 0258
E1 10 R-03 5627
The design of the Liquid heater with evaporation burner
Heat output Full load part load 5.0 kW
2.8 kW 4.0 kW
2.8 kW 5.0 kW
2.5 kW 4.0 kW
2.5 kW
Fuel Gasoline
EN 228
DIN 51625 Diesel fuel
EN 590
Fuel consumption
+/- 10 % Full load Partial load 0.705 l/h
0,395 l/h 0,560 l/h
0.395 l/h 0.620 l/h
0.310 l/h 0.495 l/h
0,310 l/h
Rated voltage 12 V
Operating voltage range 11 - 16.5 V
Rated power consumption without circulation pump
+/- 10 % (without car fan) Full load Partial load 33 W
15 W 21 W
15 W 33 W
12 W 21 W
12 W
Permissible ambient temperature: Heater - operation
- storage Metering pump: - work
- storage Summer fuel Liquid fuel -40 ... +60 °C
-40 ... +120 °C
-40 ... +20 °C
-40 ... +10 °C
-40 ... +90 °C -40 ... +80 °C
-40 ... +120 °C
-40 ... +30 °C
-40 ... +90 °C
Permissible operating pressure of the coolant 2.5 bar
Heat exchanger volume 0,075 l
The minimum amount of coolant 1.50 l
The minimum volumetric flow to coolant 200 l/h
CO2 in exhaust gases (allowable range) 8 - 12.0 % of volume
Heater dimensions without mounting parts (tolerance ± 3 mm) L = length: 218 mm
B = width: 91 mm
H = height: 147 mm without fittings
Weight of device / heater with mounting kit 2.1 kg / 8 kg
Manufacturer Webasto
Fuel type Petrol
Power 5kW
Type of passenger transport
Weight 8 kg
Voltage 12 V

Categories: Webasto Отопители жидкостные

Tags: webasto-thermo-top-Comfort-Plus

Webasto Thermo Top Comfort+ reviews

Be the first to write a review of this product!